AirFit N30 nasal mask support

Select the cushion size for your patient

1. Familiarise yourself with the cushion-sizing template provided and the cushion sizes that are available.

2. Hold the sizing template under your patient’s nose and use it to determine the most suitable cushion size. The patient’s nose should sit within the colour margins of the chosen size.

3. Select the matching cushion and try it on your patient for comfort and fit.

If your patient is between sizes, we recommend trying both sizes and choosing the size that is most comfortable for the patient.

These instructions are for general information purpose only. For full details consult the user guide.

Fitting your patient with the N30 nasal mask

1. Bring the N30 nasal mask up towards your patient’s face so that the left and right indicators are correctly aligned with their nose. Once aligned, hold the cushion under their nose.

2. Hold the bottom strap of the split band and pull the headgear over the back of your patient’s head.

3. If necessary, adjust the cushion by pulling it away from your patient’s nose and settling it back into position.

4. Adjust the split bands to achieve a comfortable fit. To loosen the mask, spread them apart, and to tighten the mask, bring them together.

5. To correct mask leak, adjust the length of the headgear through the buckle.

6. Once the AirFit N30 mask is secure and comfortable, connect the tubing to the mask and the device and get the patient ready to start therapy.

These instructions are for general information purpose only. For full details consult the user guide.

Managing leak on the AirFit N30 mask

If air escapes from the mask cushion anywhere other than the vent, try the following steps to stop the leak.

1. If the cushion is not sitting correctly, try pulling it away from your patient’s nose and settling it back into position.

2. Adjust the mask tension to achieve a secure seal by tightening or loosening the length of the headgear through the buckle. Adjust only enough for a comfortable seal and do not overtighten.

These instructions are for general information purpose only. For full details consult the user guide.

Assemble AirFit N30 nasal mask

1. Make sure you have all the N30 mask components and parts.

2. Locate the small buttonholes at each end of the headgear and insert each stabiliser into each end. Remember to keep the grey side of the headband facing outwards at all times.

3. Pull the buttonholes of the headgear over the ends of the stabilisers.

4. Hold the mask frame and stretch the headgear away to check it is securely attached. Ensure the headgear is not twisted.

5. Locate the notch on the cushion and align it with the tab on the top of the frame.

6. Attach the cushion to the frame. Push down on all edges of the cushion to ensure they are securely sealed.

These instructions are for general information purpose only. For full details consult the user guide.

Disassemble AirFit N30 nasal mask

1. Ensure the N30 mask is not connected to a CPAP device.

2. Hold the cushion securely on one side and pull it away from the frame.

3. Pull each of the end caps on the headgear until the stabilisers slide out of the buttonholes.

4. Slide the headgear off the end of each stabiliser.

These instructions are for general information purpose only. For full details consult the user guide.

Assemble AirFit N30 nasal mask

1. Make sure you have all the N30 mask components and parts.

2. Locate the small buttonholes at each end of the headgear and insert each stabiliser into each end. Remember to keep the grey side of the headband facing outwards at all times.

3. Pull the buttonholes of the headgear over the ends of the stabilisers.

4. Hold the mask frame and stretch the headgear away to check it is securely attached. Ensure the headgear is not twisted.

5. Locate the notch on the cushion and align it with the tab on the top of the frame.

6. Attach the cushion to the frame. Push down on all edges of the cushion to ensure they are securely sealed.

These instructions are for general information purpose only. For full details consult the user guide.

Daily cleaning instructions

1. Follow the AirFit N30 mask disassembly instructions to disconnect the mask cushion.

2. Soak the cushion in warm water and a mild liquid detergent.

3. Hand wash the cushion inside and out with a soft bristle brush.

4. Rinse the cushion under running tap water.

5. Leave the cushion to air dry away from direct sunlight.

These instructions are for general information purpose only. For full details consult the user guide.

Weekly cleaning instructions

1. Follow the AirFit N30 mask disassembly instructions to disconnect the mask headgear and frame.

2. Soak the headgear and frame in warm water and a mild liquid detergent.

3. Hand wash the headgear and frame. Clean the frame by scrubbing it with a soft bristle brush. Please ensure you clean the vent holes thoroughly.

4. Rinse each of the components under running tap water.

5. Shake excess water off the frame and leave each of the cleaned components to air dry away from direct sunlight.

These instructions are for general information purpose only. For full details consult the user guide.