AirFit F20 full face mask support

Cleaning the AirFit F20 mask (Daily)

1. Disassemble mask.

2. Rinse frame, elbow and cushion under running water. Clean each component with a soft brush.

3. Soak components in warm water with mild liquid detergent for up to ten minutes.

4. Shake components in water for at least one minute.

5. Brush moving parts of elbow and around vent holes.

6. Brush areas of frame where arms connect, and inside and outside the frame where the elbow connects.

7. Rinse components under running water.

8. Squeeze the arms of the frame to ensure excess water is removed then leave all components to air dry out of direct sunlight.

Haircare tips for the AirFit F20 mask

Managing leak with the AirFit F20 mask

1. Leak often occurs when your mask seal is compromised by movement, incorrect fitting or improper sizing.

2. To find the source of a leak, run your finger along the edge of your mask’s seal. Once located, adjust your headgear.

3. Resolve any leak in the upper part of your mask by adjusting your upper straps.

4. Resolve lower mask leak with your lower straps.

5. If leak persists, reseal by briefly pulling your mask away from your face, letting your cushion reinflate, and resettling your mask cushion so the cushion membrane is sitting at the top of your nasal bridge.

6. If leak continues, you may need a different size of mask. Try our sizing guide or speak to your healthcare provider about getting a different size of mask.

Sizing

1. To comfortably fit a broader range of patients, AirFit F20 features an entirely new cushion design. To help existing patients to transition to the AirFit F20 design, we recommend using our sizing guide , which is specifically designed to help patients find the right fit. You can download a copy of our sizing guide here. The arrow on the sizing guide should align with the top of your patient’s nasal bridge. The segment of the guide corresponding with the crease below your patient’s lower lip will indicate their best fit. If a patient falls between sizes, we recommend selecting the larger option for greater comfort.

2. AirFit F20 has three cushion sizes - small, medium and large. The modular design of the AirFit F20 means each size cushion easily clicks into the same mask frame.

3. Your patients can also download a copy of our sizing guide from the ResMed website.

Assembling your AirFitF20

1. Attach cushion to frame.

2. Attach the magnets ¹ .

3. Connect upper headgear straps.

4. Connect elbow to mask frame.

These instructions are for general information purposes only. For full details consult the User Guide.

1. Use of masks with magnetic components is contraindicated in patients with the following pre-existing conditions: a metallic haemostatic clip implanted in the head to repair an aneurysm and/or metallic splinters in one or both eyes.

Disassembling your AirFit F20

1. Remove elbow from frame.

2. Unclip the magnets ¹ .

3. Undo upper headgear tabs.

4. Pull strapping away from frame.

5. Pull cushion away from frame.

1. Use of masks with magnetic components is contraindicated in patients with the following pre-existing conditions: a metallic haemostatic clip implanted in the head to repair an aneurysm and/or metallic splinters in one or both eyes.

Cleaning the AirFit F20 mask (Daily)

1. Disassemble mask.

2. Rinse frame, elbow and cushion under running water. Clean each component with a soft brush.

3. Soak components in warm water with mild liquid detergent for up to ten minutes.

4. Shake components in water for at least one minute.

5. Brush moving parts of elbow and around vent holes.

6. Brush areas of frame where arms connect, and inside and outside the frame where the elbow connects.

7. Rinse components under running water.

8. Squeeze the arms of the frame to ensure excess water is removed then leave all components to air dry out of direct sunlight.

Cleaning the AirFit F20 mask (Weekly)

1. Disassemble mask. Magnets¹ can remain attached to headgear during cleaning.

2. Handwash headgear in warm water with mild liquid detergent.

3. Rinse headgear under running water. Inspect to ensure headgear is clean and detergent free. Wash and rinse again, if necessary.

4. Squeeze headgear to remove excess water.

5. Leave headgear to air dry out of direct sunlight.

These instructions are for general information purpose only. For full details consult the user guide.

1. Use of masks with magnetic components is contraindicated in patients with the following pre-existing conditions: a metallic haemostatic clip implanted in the head to repair an aneurysm and/or metallic splinters in one or both eyes.